Light of wavelength 610 nm is incident on a single slit 0.20 mm wide and the diffraction pattern is produced on a screen that is 1.5 m from the slit. What is the width of the central maximum?
A. 0.34 cm.
B. 0.68 cm.
C. 0.92 cm.
D. 1.2 cm.
E. 1.5 cm.

To calculate the binding energy per nucleon for 207Pb (lead), we need to gather some information. The atomic mass of 207Pb is 206.97588 atomic mass units (amu). We also need to know the mass of a proton and a neutron, which are approximately 1.007276 amu and 1.008665 amu, respectively.

The total mass of 207Pb can be calculated by multiplying the atomic mass by the mass of one atomic mass unit:

Total mass of 207Pb = 206.97588 amu * 1.66053906660 x 10^-27 kg/amu

The number of nucleons (protons + neutrons) in 207Pb is equal to the atomic mass number, which is 207.

The total binding energy (E) of 207Pb can be calculated using the Einstein's mass-energy equation: E = Δm * c^2, where Δm is the mass defect and c is the speed of light (3 x 10^8 m/s).

The binding energy per nucleon (BE/A) can be calculated by dividing the total binding energy by the number of nucleons (A).

Now, let's calculate the binding energy per nucleon for 207Pb:

Calculate the total mass of 207Pb in kilograms:

Total mass of 207Pb = 206.97588 amu * 1.66053906660 x 10^-27 kg/amu

Calculate the mass defect (Δm):

Mass defect = Total mass of 207Pb - (number of nucleons * mass of a proton)

Calculate the total binding energy (E):

E = Δm * (3 x 10^8 m/s)^2

Calculate the binding energy per nucleon (BE/A):

BE/A = E / number of nucleons

Performing the calculations, we find the binding energy per nucleon for 207Pb.

Learn more about energy from

https://brainly.com/question/13881533

#SPJ11

The magnetic force on the wire is 0.03 N, and the direction is perpendicular to both the magnetic field and the current direction.

To calculate the magnetic force on the wire, we can use the formula F = BILsinθ, where F is the magnetic force, B is the magnetic field, I is the current, L is the length of the wire in the magnetic field, and θ is the angle between the magnetic field and the current direction. In this case, B = 2.5 T, I = 25 A, and θ = 90° (since the wire passes straight through the field). The diameter of the cylindrical region is 12 cm, so L = 0.12 m.

Plugging in the values, we get F = 2.5 T × 25 A × 0.12 m × sin(90°) = 0.03 N. The force direction is perpendicular to both the magnetic field and the current direction, as per the right-hand rule.

Learn more about magnetic field here:

https://brainly.com/question/23096032

#SPJ11

The conditions for this two-sample game are independent random samples of her true score at the arcade and amusement park. The 10% condition is met for both groups. The distribution of scores at the arcade and amusement park has no outliers and no strong skewness. However, the normal/large sample condition is not met.

To perform a two-sample comparison, certain conditions need to be met. Let's analyze each condition based on the given information:

Independent Random Samples: The games played at the arcade and amusement park are described as random samples. This means that the scores obtained in each location are independent of each other.

10% Condition: The number of games played at the arcade (15) is less than 10% of all the games she could play at the arcade, and the number of games played at the amusement park (10) is less than 10% of all the games she could play there. Thus, the 10% condition is satisfied for both groups.

Distribution of Scores: There is no mention of outliers or a strong skewness in the distribution of scores at either the arcade or the amusement park. Therefore, we can assume that there are no outliers and no strong skewness in the data for both groups.

Normal/Large Sample Condition: The normal/large sample condition is not explicitly mentioned in the given information. Without additional details, we cannot determine whether this condition is met or not.

Based on the given information, the conditions for independent random samples and the 10% condition are met for both groups. However, we do not have enough information to determine whether the normal/large sample condition is met.

To know more about firm, visit :

https://brainly.com/question/14450371

#SPJ11

The focal length of the concave mirror is -37cm.To find the focal length of the concave mirror, we need to apply the mirror formula. The formula is: 1/f = 1/v + 1/u

Where f is the focal length, v is the image distance, and u is the object distance. According to the sign conventions, u is negative because the object is in front of the mirror, and v is negative because the image is formed behind the mirror. We are given u = -37cm and R = -22cm (since the mirror is concave), so we can find the image distance using the relation:

1/f = 1/v - 1/R
1/f = 1/-37 - 1/-22
1/f = -0.027
f = -37c

To know more about focal length visit :-

https://brainly.com/question/31755962

#SPJ11

To find the radius at which the mass rotates without moving toward or away from the origin, we can use the concept of centripetal acceleration. Centripetal acceleration is given by the formula: a = ω^2 * r

F = -T

m * ω^2 * r = -T

r = -T / (m * ω^2)

Where:

a is the centripetal acceleration,

ω is the angular speed (in radians per second),

and r is the radius.

In this case, the angular speed ω is given as 1.00 radians/s. We want to find the radius r at which the mass rotates without moving toward or away from the origin, so the centripetal acceleration must be zero.

Setting a = 0 in the centripetal acceleration formula, we have:

0 = ω^2 * r

Since ω^2 is nonzero, we can divide both sides of the equation by ω^2:

0 / ω^2 = r

Therefore, the radius at which the mass rotates without moving toward or away from the origin is 0.

Learn more about radius here

https://brainly.com/question/29595940

#SPJ11

The three essential diagnostic features of anorexia nervosa, as defined by the Diagnostic and Statistical Manual of Mental Disorders (DSM-5), are:

It is important to note that these diagnostic features must be present and significantly impair the individual's functioning in order to meet the criteria for anorexia nervosa. Additionally, there may be other associated features and behaviors,

Learn more about DSM-5 from

https://brainly.com/question/7296239

#SPJ11

To calculate the work done by a bullet traveling at a certain velocity, we need to know the mass of the bullet and the velocity at which it is moving.

W = (1/2) * 0.03 kg * (200 m/s)^2

W = (1/2) * 0.03 kg * 40000 m^2/s^2

W = 600 J (Joules)

Mass of the bullet = 30 grams = 0.03 kilograms (since 1 gram = 0.001 kilogram)

Velocity of the bullet = 200 m/s

The work done (W) is given by the formula:

W = (1/2) * m * v^2

where m is the mass of the object and v is its velocity.

Substituting the given values:

W = (1/2) * 0.03 kg * (200 m/s)^2

W = (1/2) * 0.03 kg * 40000 m^2/s^2

W = 600 J (Joules)

Therefore, the work done by the 30-gram bullet traveling at 200 m/s is 600 Joules (J).

Learn more about velocity here

https://brainly.com/question/80295

#SPJ11

The **magnitude of the angular momentum** (in kg · m^2/s) of the car relative to the center of the racetrack is **50,000 kg · m^2/s**.

Angular momentum is given by the equation: L = Iω, where L is the angular momentum, I is the moment of inertia, and ω is the angular velocity. In this case, the car is moving in a circular path, so its angular velocity can be calculated using the equation ω = v/r, where v is the linear velocity and r is the radius of the circular track.

Given that the mass of the car is 1000 kg, its linear velocity is 50 m/s, and the radius of the circular track is 100 m, we can calculate the angular velocity as follows: ω = 50 m/s / 100 m = 0.5 rad/s.

Next, we need to calculate the moment of inertia. For a point mass moving in a circular path, the moment of inertia is given by I = mr^2, where m is the mass of the object and r is the distance from the rotation axis (in this case, the center of the racetrack). Plugging in the values, we get I = 1000 kg × (100 m)^2 = 10,000,000 kg · m^2.

Finally, we can calculate the angular momentum: L = Iω = 10,000,000 kg · m^2 × 0.5 rad/s = 5,000,000 kg · m^2/s. Hence, the magnitude of the angular momentum relative to the center of the racetrack is 50,000 kg · m^2/s.

Learn more about angular momentum here:

https://brainly.com/question/29897173

#SPJ11

The correct answer is **b) Yes, because the ratio of 3/25 is less than sin(6°)**.

To determine whether there is sufficient distance for a ramp within the incline angle limit, we need to compare the ratio of the vertical distance (3 meters) to the horizontal distance (25 meters) with the value of sin(6°).

The incline angle limit is given as 0.6°. We can convert this to radians by multiplying it by π/180.

The ratio of the vertical distance to the horizontal distance (3/25) represents the tangent of the angle of inclination.

Now, we can compare the ratio of 3/25 with the value of sin(6°). Since the slope of the ramp should be less than or equal to sin(6°) to meet the code requirements, we need to check if the ratio is less than sin(6°).

By calculating sin(6°) and comparing it with the ratio of 3/25, we find that the ratio of 3/25 is indeed less than sin(6°). Therefore, there is sufficient distance for a ramp within the given incline angle limit.

Learn more about angle of inclination here:

https://brainly.com/question/29360090

#SPJ11

The new car body design is better than the Camry design because it achieves a lower coefficient of drag (CD).

What is coefficient of drag (CD)?

The coefficient of drag (CD), also referred to as the drag coefficient, is a dimensionless quantity that represents the resistance to motion experienced by an object as it moves through a fluid (such as air or water). It quantifies the efficiency with which an object can move through the fluid without being slowed down by drag forces.

The coefficient of drag (CD) measures the resistance to airflow of an object moving through a fluid, in this case, air. A lower CD value indicates better aerodynamic performance.

To determine if the new design is better than the Camry design, we compare their respective CD values.

Given that the CD of the Camry is 0.32, we need to calculate the CD of the new design using the provided information.

Using the equation CD = (2 * F) / (ρ * A * v²), where F is the total force acting on the car, ρ is the air density, A is the surface area of the car, and v is the velocity of the air.

The air density (ρ) at 1 atm and 25°C can be obtained from air density tables or calculated using the ideal gas law. Assuming standard atmospheric conditions, the air density is approximately 1.184 kg/m³.

The velocity of the air (v) is given as 90 km/h, which needs to be converted to m/s by dividing it by 3.6. Thus, v = 90 km/h / 3.6 = 25 m/s.

Substituting the values into the equation, CD = (2 * 300 N) / (1.184 kg/m³ * 6 m² * 25 m/s)², we can solve for CD.

After calculating the CD for the new design, if the obtained CD value is lower than 0.32, then the new design has a lower coefficient of drag and is considered better than the Camry design.

To know more about  coefficient of drag (CD), refer here:

https://brainly.com/question/14040167#

#SPJ4

Complete question:

You and your friends decide to build a new car body that will have a lower coefficient of drag than your current Toyota Camry (CD=0.32). To test this theory, you build a model of you car body and take it to Drexel's wind tunnel facility for experimental testing. You set the wind tunnel specifications to 1 atm, 25°C, and 90 km/h. The height of your car is 1.40 m and the width is 1.65 m. The total surface area of the body design is 6 m². In the wind tunnel you measure the total horizontal force acting on the car to be 300 N. Is your new design better than the Camry design?

To find the battery's electromotive force (emf) in a charging circuit with a capacitor, resistor, and battery, we can use the formula that relates the current (I), time constant (τ), and the emf (ε):

I = ε / R * (1 - e^(-t/τ))

Capacitance (C) = 20 μF = 20 x 10^-6 F

Resistance (R) = 5.0 kΩ = 5.0 x 10^3 Ω

Current (I) = 0.54 mA = 0.54 x 10^-3 A

Time (t) = 0.15 s

where:

I is the current,

ε is the emf,

R is the resistance, and

τ is the time constant given by τ = R * C, where C is the capacitance.

Capacitance (C) = 20 μF = 20 x 10^-6 F

Resistance (R) = 5.0 kΩ = 5.0 x 10^3 Ω

Current (I) = 0.54 mA = 0.54 x 10^-3 A

Time (t) = 0.15 s

First, let's calculate the time constant:

τ = R * C = (5.0 x 10^3 Ω) * (20 x 10^-6 F)

Now, we can rearrange the formula to solve for the emf (ε):

ε = I * R * (1 - e^(-t/τ))

Substituting the given values:

ε = (0.54 x 10^-3 A) * (5.0 x 10^3 Ω) * (1 - e^(-0.15 s / τ))

To find the emf, we need the value of τ. Please provide the capacitance or the resistance value so that we can calculate the time constant and determine the battery's emf.

Learn more about electromotive here

https://brainly.com/question/30083242

#SPJ11

The Coulomb force, which describes the electrostatic interaction between charged particles, follows an inverse square law. This means that the force decreases as the square of the distance between the charged particles increases.

Similarly, in the solar system, the force that keeps the planets in orbit around the sun, known as the gravitational force, also follows an inverse square law. As the distance between the planets and the sun increases, the gravitational force weakens.

Due to this similarity in the mathematical behavior of the Coulomb force and the gravitational force, early models of atoms were conceptualized as miniature solar systems.

Electrons were considered to orbit the nucleus in a manner analogous to how planets orbit the sun.

While the Bohr model of the atom has since been replaced by quantum mechanics, the analogy between the inverse square laws of Coulomb's law and gravity helped shape early understandings of atomic structure.

To know more about electrostatic, refer here:

https://brainly.com/question/14889552#

#SPJ11

Part A:To calculate the oscillation frequency of the circuit, we can use the formula: f = 1 / (2π√(LC))

C = 16.0 μF = 16.0 × 10^(-6) F

L = 0.270 mH = 0.270 × 10^(-3) H

where f is the frequency, L is the inductance, and C is the capacitance.

Given:

C = 16.0 μF = 16.0 × 10^(-6) F

L = 0.270 mH = 0.270 × 10^(-3) H

Substituting the values into the formula:

f = 1 / (2π√(0.270 × 10^(-3) × 16.0 × 10^(-6)))

Calculating the frequency: f ≈ 1.27 × 10^3 Hz

Therefore, the oscillation frequency of the circuit is approximately 1.27 kHz.

Part B: The energy stored in the capacitor at time t = 0 ms is given by the formula: E = 1/2 CV^2

where E is the energy, C is the capacitance, and V is the voltage.

C = 16.0 μF = 16.0 × 10^(-6) F

V = 120.0 V

Substituting the values into the formula:

E = 1/2 × 16.0 × 10^(-6) × (120.0)^2

Calculating the energy: E ≈ 115.2 μJ

Therefore, the energy stored in the capacitor at time t = 0 ms is approximately 115.2 μJ.

Part C: The energy stored in the inductor at time t = 1.30 ms is given by the formula: E = 1/2 LI^2

where E is the energy, L is the inductance, and I is the current.

Since we are not given the current directly, we would need additional information or equations to calculate the energy stored in the inductor at a specific time.

Learn more about oscillation here

https://brainly.com/question/22499336

#SPJ11

The binding energy per nucleon for 64Zn is approximately -7.996 MeV/nucleon.

To calculate the binding energy per nucleon (BE/A) for 64Zn, we need to determine the total binding energy and then divide it by the number of nucleons.

64Zn is about 49% of natural zinc, so we assume the mass number (A) of 64Zn is 64.

The mass of a proton or neutron (u) is approximately 1 u = 1.007825 u.

First, we calculate the total binding energy (BE) for 64Zn:

BE = (A × u - m(64Zn)) × c²

The mass of 64Zn can be calculated as:

m(64Zn) = A × u

m(64Zn) = 64 × 1.007825 u

BE = (64 × 1.007825 u - 64 × 1 u) × (931.5 MeV/c²)

BE = (64 × 1.007825 - 64) × 931.5 MeV

Next, we calculate BE/A, the binding energy per nucleon:

BE/A = BE / A

BE/A = [(64 × 1.007825 - 64) × 931.5] / 64

BE/A ≈ -7.996 MeV/nucleon

Therefore, the binding energy per nucleon for 64Zn is approximately -7.996 MeV/nucleon. The negative sign indicates that energy is released when nucleons are brought together to form the nucleus.

To know more about  nucleon visit:

https://brainly.com/question/14622763

#SPJ11

The maximum possible value for distance, d is calculated as equal to 80.9 meters. This means that if the car is farther away than 80.9 meters, the bear will catch up to the tourist before the tourist reaches the car.

The tourist's speed is given as 5.66 m/s, so we can find the time it takes for the tourist to reach the car by dividing the distance d by 5.66 m/s: time = d / 5.66

Now we need to figure out how far the bear can run in this amount of time. We can use the formula: distance = speed x time

The bear's speed is given as 7.46 m/s, and the time it takes for the tourist to reach the car is d / 5.66. So the distance the bear can run in this time is: distance = 7.46 x (d / 5.66)

Now we can set up an equation to find the maximum possible value for d. We know that the bear starts 25.9 m behind the tourist, and the tourist reaches the car safely, which means the bear doesn't catch up. So the maximum distance the bear can run is equal to the distance between the tourist and the car, which is: d - 25.9

Setting this equal to the distance the bear can run, we get: d - 25.9 = 7.46 x (d / 5.66)

Now we can solve for d: d - 25.9 = 1.32d
0.32d = 25.9

Thus, d = 80.9

So, the maximum possible value for d is 80.9 meters.

To know more about distance, refer

https://brainly.com/question/26550516

#SPJ11

The radius of the circle when the string breaks is approximately 0.285 m.

To find the radius at which the string breaks, we need to consider the tension in the string. As the string is pulled from below, the tension in the string increases until it reaches the breaking strength, at which point the string breaks.

In this scenario, the tension in the string provides the necessary centripetal force to keep the block moving in a circular path. The centripetal force is given by the equation: F = mv²/r, where F is the tension, m is the mass of the block, v is the tangential speed, and r is the radius of the circle.

In this case, the breaking strength of the string is given as 30.0 N. At the point of breaking, the tension in the string equals the breaking strength. Plugging in the given values, we can solve for the radius:

30.0 N = (0.270 kg) × (4.00 m/s)² / r

Simplifying the equation and solving for r, we find:

r ≈ (0.270 kg) × (4.00 m/s)² / 30.0 N ≈ 0.285 m

Therefore, the radius of the circle when the string breaks is approximately 0.285 m.

know more about breaking strength click here:

https://brainly.com/question/29794188

#SPJ11

the relativistic addition of velocities formula: v = (u + w) / (1 + uw/c^2), where v is the relative  are  velocity in a   between two objects moving at velocities u and w relative to a third reference frame. In this case, u is the velocity of the spaceship relative

the speed of the canister relative to the Earth is not simply 1.1c (the sum of the velocities of the spaceship and canister) is due to the effects of special relativity. At such high speeds, the relativistic addition of velocities formula must be used to properly calculate the relative velocities between objects moving at significant fractions of the speed of ligh

where V is the combined velocity, v1 is the velocity of the spaceship (0.55c), v2 is the velocity of the canister relative to the spaceship (0.55c), and c is the speed of light.  Plug in the values into the formula  V = (0.55c + 0.55c) / (1 + (0.55c * 0.55c) / c^2)Simplify the equation.V = (1.10c) / (1 + 0.3025) Complete the calculation .V = 1.10c / 1.3025V ≈ 0.89c the speed of the canister relative to the Earth is approximately 0.89c, which is option C.

To know more about velocity Visit ;

https://brainly.com/question/30559316

#SPJ11

The  voltage v (in Volts) across the resistor can be calculated using the formula P = V^2/R, where P is the power dissipated  resistor, R is the resistance of the resistor  and V is the voltage across the resistor. In this scenario dissipated in the resistor is given as 11.0W,

Since we are assuming that the voltage across the resistor is constant, we can use the formula P = V^2/R to calculate the voltage v (in Volts) across the resistor. Rearranging the formula, we get V^2 = P * R. Substituting the given values, we get V^2 = 11.0W * 8.0Ω = 88.0WΩ. Taking the square root of both sides, we get V = sqrt(88.0) = 9.38V (rounded to two decimal places).

the voltage across a resistor. In this case, the main answer can be found by using the formula P = V^2/R, where P is the power dissipated, V is the voltage across the resistor, and R is the resistance.  Rearrange the formula to solve for V: V^2 = P * R V^2 = 11.0 W * 8.0 Ω  Calculate V^2: V^2 = 88.0 V^2  Find the square root to get V: V = √88.0 V^2 V ≈ 9.38 V The voltage ross the resistor, when connected to an unknown network N and immersed in an isolated water bath, is approximately 9.38 volts. This was determined by using the power dissipation formula, substituting the given values, and solving for the voltage.

To know more about power Visit;

https://brainly.com/question/31734541

#SPJ11

The type of massage that involves a soft continuous stroking movement is called Effleurage.

Effleurage is a massage technique commonly used in various massage modalities, including Swedish massage, aromatherapy massage, and relaxation massage.

During effleurage, the massage therapist applies gentle, gliding strokes with their hands or fingertips over the client's body. The strokes are long, smooth, and rhythmic, creating a continuous and flowing motion. Effleurage can be performed using different levels of pressure, depending on the client's preference and the purpose of the massage.

Effleurage serves several purposes in a massage session. It helps to warm up the muscles, relax the client, and promote the circulation of blood and lymphatic fluids. It also aids in the application of massage oils or lotions and provides a soothing and comforting sensation to the recipient.

Overall, effleurage is a foundational technique in massage therapy that helps create a relaxing and enjoyable experience for the client while providing various physiological and psychological benefits.

Learn more about movement here

https://brainly.com/question/24745731

#SPJ11

Weight is the force experienced by an object due to gravity. It is calculated by multiplying the mass of the object by the acceleration due to gravity.

On the Moon, the acceleration due to gravity (g) is 2 m/s^2.

To calculate the weight of the person on the Moon, we can use the formula:

Weight = mass * acceleration due to gravity.

Given that the mass of the person is 45 kg and the acceleration due to gravity on the Moon is 2 m/s^2, we have:

Weight = 45 kg * 2 m/s^2.

Calculating this expression, we find:

Weight = 90 N.

Therefore, the person would weigh 90 Newtons on the Moon.

Hence, the weight of the person on the Moon is 90 Newtons.

Learn more about acceleration due to gravity here:

https://brainly.com/question/29135987

#SPJ11

To determine the magnetic field at point P, we can apply Ampere's law. Ampere's law states that the magnetic field around a closed loop is directly proportional to the current passing through the loop.

Consider a rectangular Amperian loop around point P as shown in the figure. The length of the loop perpendicular to the current is x, and the length parallel to the current is L. The sides of the loop parallel to the current do not contribute to the magnetic field at point P.

The magnetic field along the curved portion of the loop (the wire segment) will be constant and given by the formula:

B₁ = (μ₀ * I) / (2π * r₁)

where B₁ is the magnetic field along the curved portion of the loop, μ₀ is the permeability of free space (4π × 10^(-7) T·m/A), I is the current, and r₁ is the distance from the wire to point P along the curved segment.

Now, we need to consider the contribution of the straight segment of the loop. Since it is parallel to the current, it does not contribute to the magnetic field at point P.

Therefore, the magnetic field at point P is equal to the magnetic field along the curved segment of the loop, which is given by B₁.

The direction of the magnetic field can be determined using the right-hand rule. If we curl the fingers of our right hand in the direction of the current, the thumb points in the direction of the magnetic field at point P.

So, the magnetic field at point P has a magnitude of B₁ and its direction is perpendicular to the plane of the figure, pointing into the page.

Learn more about magnetic field at point P from

https://brainly.com/question/31424843

#SPJ11

We can use this acceleration to find the orbital period T. The exact expression for T is T = 2π√[(r^3)/(G(M + 2m))] where G is the gravitational constant.

To find the orbital period T for the two planets with mass m orbiting a star of mass M at a radius r, we can use the gravitational force and centripetal force acting on each planet. Each planet experiences gravitational force from the star and the other planet. The net force acting on a planet is:

F_net = F_star + F_planet

By using Newton's Law of Gravitation and Centripetal force equations, we get:

GmM/r^2 + Gm^2/(2r)^2 = mv^2/r

Solving for the velocity (v), we get:

v = sqrt(G(M + m/4)/r)

Now, we know that the orbital period T is related to the circumference of the orbit and the velocity by:

T = 2πr/v

Substitute the value of v into the equation, and we have:

T = 2πr/sqrt(G(M + m/4)/r)

This is the exact expression for the orbital period T for the given scenario.

To learn more about gravitational visit;

https://brainly.com/question/3009841

#SPJ11

The term for the precision of a laser beam that is based on the area exposed, the time activated, and the power setting is known as laser spot size.

Laser spot size is an important parameter that determines the accuracy and effectiveness of laser applications, such as laser cutting, welding, and engraving. The spot size is determined by the optics used to focus the laser beam and is typically measured in microns.

A smaller spot size allows for higher precision and finer details in laser processing, but may also require higher power settings and longer processing times. It is important to carefully choose the appropriate spot size for a given application to achieve the desired results with optimal efficiency.

Laser fluence refers to the amount of energy delivered by a laser beam to a specific area. It is typically measured in units of energy per area, such as joules per square centimeter (J/cm²). Laser fluence takes into account the area exposed, the time activated, and the power setting of the laser.

By adjusting these factors, one can achieve the desired precision for a specific application, ensuring optimal results.

To know more about Laser fluence visit -

brainly.com/question/27853311

#SPJ11

The radius of the copper cable is approximately 0.004 m.


The resistance of the copper cable can be calculated using Ohm's law: R = V/I, where V is the potential difference and I is the current. Thus, R = (1.6 x 10^-2 V) / (1200 A) = 1.33 x 10^-5 ohms.

The resistance of a cylindrical conductor is given by R = (ρL) / A, where ρ is the resistivity of the material, L is the length of the conductor, and A is its cross-sectional area. Solving for the area, we get A = (ρL) / R.  

Assuming the cable is made of pure copper with a resistivity of 1.68 x 10^-8 ohm-meters, and using the length of the two points on the cable, which is 0.24 m, we can calculate the area of the cross-section of the cable. A = (1.68 x 10^-8 ohm-meters x 0.24 m) / (1.33 x 10^-5 ohms) = 0.0000757 m^2.  

Finally, we can solve for the radius using the formula for the area of a circle, A = πr^2. The radius of the cable is approximately 0.004 m.

Learn more about Ohm's law here:

https://brainly.com/question/14796314

#SPJ11

In a parallel circuit, as more resistors (R) are added, the total current in the circuit (Itotal) increases.

This is because in a parallel circuit, the total current is divided among the different branches according to the individual resistances. Each resistor provides an additional pathway for current to flow, resulting in an overall decrease in the total resistance of the circuit.

According to Ohm's Law (I = V/R), a decrease in total resistance (R) leads to an increase in total current (I). Therefore, adding more resistors in parallel decreases the total resistance and increases the total current in the circuit.

Learn more about  parallel circuit, as more resistors from

https://brainly.com/question/907760

#SPJ11

The acceleration of a proton in an electric field of 700 N/C is 4.4x10^-14 m/s^2, in the direction of the field.

The acceleration of a charged particle in an electric field is given by the formula a = F/m, where F is the electric force acting on the particle and m is its mass. For a proton of mass 1.67x10^-27 kg and charge 1.6x10^-19 C, the electric force is F = qE, where E is the electric field intensity.

Plugging in the values, we get F = 1.6x10^-19 C x 700 N/C = 1.12x10^-16 N. Therefore, the acceleration of the proton is a = F/m = 1.12x10^-16 N / 1.67x10^-27 kg = 6.69x10^10 m/s^2. However, since this value is very large, we need to convert it to nanometers per second squared (nm/s^2) to make it more meaningful.

This gives us a value of 4.4x10^-14 m/s^2, which is the magnitude of the acceleration. The direction of the acceleration is the same as the direction of the electric field, which in this case is the positive x-axis.

Learn more about electric field here:

https://brainly.com/question/30544719

#SPJ11

The tension on the cable is approximately 5157.8 Newtons.

To find the tension on the cable, we need to use the formula T = mg + ma, where T is tension, m is mass, g is the acceleration due to gravity (9.81 m/s2), and a is the acceleration of the object.
In this case, m = 780 kg and a = -3.2 m/s² (negative because it's slowing down).
T = 780 kg * (9.81 m/s² - 3.2 m/s²)
T = 780 kg * 6.61 m/s²
T ≈ 5157.8 N
To know more about tension, visit:

https://brainly.com/question/31715338

#SPJ11

If you are driving at 60 miles/ hr along a straight road and you look to the side for 2.0s. During the 2.0 seconds of inattentiveness, you travel 1/30 miles.

Speed is a measure of how quickly an object moves or the rate at which an object changes its position. It is a scalar quantity, meaning it only has magnitude and no direction. Speed is typically expressed in units of distance per unit of time, such as meters per second (m/s), kilometers per hour (km/h), or miles per hour (mph).

To calculate the distance traveled during the inattentive period, you can use the formula:
Distance = Speed × Time
In this case, you're driving at 60 miles per hour and looking to the side for 2.0 seconds. To keep the units consistent, we need to convert the speed to miles per second:
60 miles/hr × (1 hr / 3600 seconds) = 1/60 miles/second
Now, you can plug in the values into the formula:
Distance = (1/60 miles/second) × 2.0 seconds
Distance = 1/30 miles
To know more about scalar quantity, visit:

https://brainly.com/question/30895553

#SPJ11

(a) The period of rotation of the tires is approximately 0.069 seconds. (b) In one second, a tire rotates through an angle of approximately 91.2 radians.


(a) First, we need to find the circumference of the tire, which is the distance it covers in one rotation. Circumference (C) = 2 * π * radius, so C = 2 * π * 0.34 m ≈ 2.14 m. Now, we can find the number of rotations per second (frequency) by dividing the speed by the circumference: frequency = 31 m/s / 2.14 m ≈ 14.49 rotations/s. To find the period of rotation (time for one rotation), take the reciprocal of the frequency: period ≈ 1 / 14.49 s ≈ 0.069 seconds.

(b) The tire rotates 14.49 times per second, so in one second, it covers an angle of 14.49 * 2π radians, which is approximately 91.2 radians.

Learn more about frequency here:

https://brainly.com/question/21471742

#SPJ11

There are two bowls having spinning marbles in them, one bowl contains marble with water and the other bowl contain only marble without water, the marble will stop first is without water

This is because of the law of conservation of energy, which states that energy cannot be created or destroyed, but can only be transferred or converted from one form to another.When the bowl with marbles without water spins, the marbles transfer their kinetic energy to the bowl, which slows them down and eventually stops them.

However, when the bowl with marble and water spins, the kinetic energy of the marbles is transferred to the water. The water absorbs some of the energy and moves in the opposite direction, creating resistance, this resistance slows down the marbles, but not as quickly as in the bowl with only marbles. Therefore, when two bowls have spinning marbles, the one with only marbles without water will stop first,

Learn more about kinetic energy at

https://brainly.com/question/22174271

#SPJ11