Please answer ASAP!!
Which statement correctly describes why the electric pole has bent?

A.) Tensile stress acting on the pole caused it to bend.

В.) Compressive stress acting on the pole caused it to bend

С.) The force acting on the pole exceeded its yield strength.

D.) The force acting on the pole exceeded its compressive strength.

Answer: Ohm Ω

Explanation:

The resistance can be defined as the hindrance offered to the flow of current. Lower the current the higher is the resistance. The SI unit of resistance is ohm Ω. When one ampere current flows from an object or wire the application of one volt of potential difference on it the resistance so produce is one ohm. Resistance can be achieved by the application of the certain gadgets in the circuit which can prevent the flow of excess current from devices and can prevent shock circuit.

Answer: c. Centre of pressure​

Explanation:

Pressure is applied on a surface when a force is exerted on a particular point on that surface by another object when the two come into contact with each other.

The point where the pressure is applied is known as the centre of the pressure with the force then spreading out from this point much like an epicentre in an earthquake.

Explanation:

(1) 174 inch

(2)1 foot 3.6 inches

(3) 39.649 centimetre

(4)175 decimeter

(5)26.25 feet

Answer:

kindly check the drawing of the  FBD of the beam with reactions at A & B. A is a pin, B is a roller in the attached picture.

Explanation:

Without further ado, let's dive straight into the solution to the question above. From the diagram of the FBD of the beam with reactions at A & B it can be shown that the reaction moment is anticlockwise while the moment is clockwise.

The system is at equilibrium and the it does not matter where you place the couple (pure) moment.

The distance from A to C can either be equal or not. If AY = 2.15 kN and M = 25.8. Then, the distance between A and B = 25.8/2.15 = 12m.

Answer:

hello your question is incomplete attached below is the missing equation related to the question  

answer : 40.389° , 38.987° , 38° , 39.869° , 40.265°

Explanation:

Determine the friction angle at each depth

attached below is the detailed solution

To calculate the vertical stress = depth * unit weight of sand

also inverse of Tan = Tan^-1

also qc is in Mpa while σ0 is in kPa

Friction angle at each depth

2 meters = 40.389°

3.5 meters  = 38.987°

5 meters = 38.022°

6.5 meters = 39.869°

8 meters = 40.265°

Answer:

The answer is below

Explanation:

The lengths of the rods are not given.

Let us assume the length of rod 1 = 1500 mm and the length of rod 2 = 800 mm

Solution:

The normal strain is defined as the change in member length δ divided by the initial member length L. The normal strain (ε) is:

ε = δ / L

δ = εL

For rod 1:

[tex]\delta_2=\epsilon_2 L_2\\\\\delta_2=0.0010\ mm/mm*1500\ mm=1.5\ mm[/tex]

The axial elongation of rod 2 is 1.5 mm. Since rigid bar ABC is attached to rod 2, the rigid bar move down by same amount.

The rigid bar moves down 1.8 mm but rods 1 will not be stretched by this amount. Because there is a gap between rod (1) and the rigid bar at B, the first deflection of 1 mm would not cause an elongation in rod 1. Therefore, the elongation in rods (1) is:

[tex]\delta_1=1.5\ mm-1\ mm=0.5\ mm[/tex]

The normal strain in rod 1 is:

[tex]\epsilon_1=\frac{\delta_1}{L_1} =\frac{0.5\ mm}{800\ mm} \\\\\epsilon_1=0.000625\ mm/mm[/tex]

Answer:

NICE

Explanation:

Answer:

True

Explanation:

It's just because of the processing

Answer:

You can look it up

Explanation: if you don't know what it is look it up on .

Answer:

Explanation:

How does an aircraft take off?

They are lift, weight, thrust and drag. Lift pushes the airplane up. The way air moves around the wings gives the airplane lift. The shape of the wings helps with lift, too.

HOPE THIS HELPS!

Answer:

The condition does not hold for a compression test

Explanation:

For a compression test the engineering stress - strain curve is higher than the actual stress-strain curve and this is because the force needed in compression is higher than the force needed during Tension.  The higher the force in compression leads to increase in the area therefore for the same scale of stress the there is more stress on the Engineering curve making it higher than the actual curve.

Hence the condition of : on the same scale for stress, the tensile true stress-true strain curve is higher than the engineering stress-engineering strain curve. does not hold for compression test

Answer:

No because it is something to gain knowledge of peoples lives.

Answer: i was not suprised because, it is something all people need to know to gai  knowledege about it.

Answer:

the pitch point im pritty sure what is is

The point of contact of two pitch circles of mating gears is called the pitch point.

A pitch point is where two pitch circles frequently come into touch. A common point of contact between two pitch circles of mating gears is called a pitch point. The pitch circle and is centered on the top of the teeth. Dedendum circle, also known as the root circle, is the circle traced through the base of the tooth.

The pressure angle, often known as the “tooth shape,” is the angle at which pressure from one gear's tooth is transferred to another gear's tooth. Pure rolling motion will occur at pitch point.

Therefore, it is pressure point.

Learn more about the pressure point, refer to:

https://brainly.com/question/2510654

#SPJ6

Answer:

True

Explanation:

Many chickens lay eggs of that size and eggs from chickens are the most commonly used

tesla lol how did you not know that?

Answer:

Tesla is a car that is able to drive automatically.