The final temperature of a rhodium metal that has a specific heat of 0.240 J/gK is 328.52K (55.52°C).
How to calculate final temperature?The final temperature of a metal can be calculated using the following formula:
Q = mc∆T
Where;
Q = quantity of heat absorbed or releasedm = mass of substancec = specific heat capacity∆T = change in temperatureAccording to this question, 586J of heat is added to an 80.0 g block of rhodium metal that is initially at 25.0°C. The final temperature can be calculated as follows:
586 = 80g × 0.240J/gK × {T - 298}
586 = 19.2T - 5721.6
19.2T = 6307.6
T = 328.52K
Therefore, the final temperature of a rhodium metal that has a specific heat of 0.240 J/gK is 328.52K (55.52°C).
Learn more about final temperature at: https://brainly.com/question/11244611
#SPJ1
2.1.4 practice you measure the mass of an apple using a balance. you get these three measurements:
The trials are precise but are not accurate.
The degree to which a measured value approaches a standard or true value is referred to as accuracy. Accuracy is achieved by taking small readings. On the other hand, precision is defined as how closely two or more measurements match one another.
Therefore, accuracy is the degree to which a measurement is near its real value, whereas precision is the degree to which subsequent measurements taken in the same circumstances get the same results.
Now, the three readings obtained by weighing an apple using a balance are trial 1, trial 2, and trial 3.
The mass of the apple during the first trial =167.0g.
The mass of the apple during the second trial =166.9g.
The mass of the apple during the third trial = 167.2g
The true mass of the apple =172g
Therefore, a true mass describes your results in terms of precision and accuracy.
Now, in your three trials to measure the weight of the mass of the apple, your readings replicates were extremely near to each other. As a result, your trials are precise. However, the true mass was 172 g, and if you average your three trials, you would get roughly 167.1 g, which isn't very near to the true mass. As a result, your trials are precise but not accurate.
Read more about Accuracy and Precision:
https://brainly.com/question/15276983
#SPJ4
You measure the mass of an apple using a balance. You get these three measurements: Trial 1: 167.0 g Trial 2: 166.9 g Trial 3: 167.2 g You know that the true mass of the apple is 172 g. Describe your results in terms of precision and accuracy. Explain your answer.
A student in a lab measured the mass of 380 ml of regular coca cola and the mass of 380 ml of diet coca cola. He found the mass of regular coca cola to be 384 g, and the mass of diet coca cola to be 370g. What physical property of both drinks can you calculate based on the data obtained in experiment 1?.
The physical property of both drinks that we can calculate based on the data obtained is density
The density formula and the procedure we will use is:
d = m/v
Where:
v= volumed= densitym= massInformation about the problem:
v(regular coca cola)= 380 mlm(regular coca cola)= 384 gv(diet coca cola)= 380 mlm(diet coca cola)=370 gd(diet coca cola)= ?d(regular coca cola)= ?Applying the density formula, we get:
d(regular coca cola) = m(regular coca cola)/v(regular coca cola)
d(regular coca cola) = 384 g / 380 ml
d(regular coca cola) = 1.0105 g/ml
d(diet coca cola) = m(diet coca cola)/v(diet coca cola)
d(diet coca cola) = 370 g / 380 ml
d(diet coca cola) = 0.9737 g/ml
What is density?It is a physical quantity that expresses the ratio of the body mass to the volume it occupies.
Learn more about density in: brainly.com/question/1354972
#SPJ4
tion 6 of 30
at type of nucleus is the strong nuclear force greater than the
rostatic force?
Answer:
bro you can explane why is so hard
Explanation:
a sample of an organic compound (a nonelectrolyte) weighing 1.35 g lowered the freezing point of 10.0 g of benzene by 3.66 °c. assuming ideal solution behavior, calculate the molar mass of the compound.
A sample of an organic compound (a nonelectrolyte) weighing 1.35 g lowered the freezing point of 10.0 g of benzene by 3.66 °c. assuming ideal solution behavior molar mass of the compound is 189 g mol⁻¹
Here given data is a sample of an organic compound which is nonelectrolyte and weighing of this compound is 1.35 g lowered the freezing point 0.0 g of benzene by 3.66 °c then we have to find molar mass of the compound=?
So here from the given data the freezing point lowering (ΔTf) is known to be 3.66 °C. also, Kf for benzene can be obtained 11.2 means (Kf = 5.12 °C/m). therefore, the equation ΔTf = Kfm can be used to find the molality of the solution. the definition of molality is moles of solute per kilogram of solvent. by using the mass of the solvent, benzene, the number of moles of solute may be found. using this information with the grams of solute, the molar mass of the organic solute may be found
ΔTf = Kfm
3.66 °C = (5.12 °C/m) × m
M=mole of solute/kg solvent=0.715
Molality=0.715 mol solute/kg solvent=0.715 m
0.715 m=x/0.010 kg benzene
Xmol=0.715 × 0.010=7.15×10⁻³mol solute
Mol=g/molar mass
7.15×10⁻³mol solute=1.350g/molar mass
Molar mass= 189 g mol⁻¹
Know more about molar mass
https://brainly.com/question/28607404
#SPJ4
Which of the following represents a pair of isotopes
Considering the definition of isotope and its notation, the correct answer is option B: the pair 12C and 14C is a pair of isotopes.
Definition of atomic numberThe atomic number (Z) is the total number of protons that make up the atomic nucleus of a given chemical element.
Definition of atomic massThe atomic mass (A) is obtained by adding the number of protons and neutrons in a given nucleus of a chemical element.
Definition of isotopeThe same chemical element can be made up of different atoms, that is, their numbers of protons are the same, but the number of neutrons is different. These atoms are called isotopes of the element.
In other words, isotopes of the same element have the same atomic number (Z) but each has a different mass number (A). This indicates that within each chemical element there are several atomic species that differ in their atomic mass.
The isotopes are located in the same place within the Periodic Table.
Isotopes of an element have the same chemical properties but differ somewhat in physical properties because they differ in atomic mass.
The notation of an isotope is given as shown in the attached image.
Pair of isotopes in this caseConsidering the definition of isotope and its notation, the correct answer is option B: the pair 12C and 14C is a pair of isotopes.
Learn more about isotopes:
brainly.com/question/27407210
brainly.com/question/1598931
brainly.com/question/13255613
brainly.com/question/28312353
#SPJ1
Kaseem is taking his bicycle for a ride. His bicycle is a system, and its main purpose is to provide transportation. What is the desired output of this system
The desired output of this system which involves a bicycle for transportation is the bicycle forward motion.
What is Transportation?This is defined as the process in which goods and people are moved from one location or place to another through the use of vehicle such as bicycle, motorcycle etc.
When riding a bicycle, the input is the force which is exerted on the pedal with the use of the legs and it then results in the bicycle moving forward (forward motion) and is referred to as the output which is therefore the reason why it was chosen as the most appropriate choice.
Read more about Transportation here https://brainly.com/question/27667264
#SPJ1
protecting against pathogens that have got into the body A.plasmaB.red blood cellsC.white blood cells
Answer: white blood cells
Explanation: they protect you from illnesses and diseases
If you add a chunk of zinc to a beaker of acid and zinc shavings to another beaker of acid, the sample with the zinc shavings will react faster. What property causes the increase in rate?.
The property that caused the sample with zinc shavings to react faster than the sample with the chunk of zinc is surface area.
The rate of a reaction is the rate at which reactants form products in a chemical reaction. There are various properties that increase or decrease the rate of reactions, which include temperature, catalyst, surface area and nature of the reaction.
In the question above, the main property that increased the rate of the reaction is surface area. Surface area is the amount of a solid reactant that is exposed. The more the surface area exposed, the faster the reaction.
The beaker of acid with the chunk of zinc is slower, because the zinc has less of its surface area exposed to the acid. In the second sample, reaction takes place on each of the zinc shavings, which will increase the rate at which products are going to form.
Learn more about zinc here:
https://brainly.com/question/21811823
#SPJ4
? Question
elect the correct answer from each drop-down menu.
Complete this paragraph, which describes an ice cube changing from a solid to a liquid to a gas.
Water can exist in three states of matter. Imagine examining the changes of state from solid to liquid to gas by adding
▼ to ice. What would change or not change?
The size of the water molecules
As water changes state, the mass of the sample
However, the
of the water molecules does change during a change in state. The
evidence that supports this conclusion is that the volume of the sample changes.
Submit
As water changes state, the mass of the sample changes.
What happens when water molecules change from liquid to gas?The hydrogen bonds between water molecules completely dissolve when the heat is increased during the boiling process, allowing water molecules to escape into the air as gas.
The potential energy decreases as that of the liquid cools, which causes the molecules to begin to move more slowly. Ice is created when the molecules of water adhere to one another at a temperature of about 0°C. The molecules are still moving despite being in this solid state; we can't see it.
Water's molecular structure never changes, even though it can transition from a liquid state to a solid or gas state and back again.
To know more about potential energy :
https://brainly.com/question/24284560
#SPJ9
The chemical equation below is incorrect.
Zn + HCI ---> ZnCl2 + H₂
O Zn + 2HCI ---> ZnCl2 + H₂
O 2Zn + 2HCI ---> ZnCl2 + H2
O Zn + HCI ---> ZnCl2 + H₂
O 4Zn + 2HCI ---> ZnCl2 + H2
Many types of scientific equipment are used to perform different functions in the science lab which if the following combinations of equipment would be needed to bring one liter of water to 85 c
graduated cylinder, beaker, thermometer and hot plate can be used bring one liter of water to 85 c
graduated cylinder, measuring cylinder or mixing cylinder is the common piece of laboratory equipment that is used to measure the volume of liquid, narrow cylindrical shape and Each marked line on the graduated cylinder represents the amount of liquid that has to been measured- beaker is a glass container with flat bottom which scientists use to hold liquids. ... In Britain, a beaker is a drinking cup mainly used by children, but in the U.S. the word is primarily used to mean a cylindrical glass vessel for mixing, measuring, and pouring liquid chemicals- The thermometer is the instrument used for measuring temperature, sealed glass tube that contains column of liquid.- hot platelearn more about equipments here-
https://brainly.com/question/932658
#SPJ9
Why is the ph of a 0. 1 m solution of acetic acid in water higher than that of a 0. 1 m solution of hcl in water?.
The pH of a 0.1 M solution of acetic acid in water is higher than that of a 0.1 M solution of HCl in water because the acetic acid does not fully ionizes in water but HCl completely ionizes in water.
Acetic acid being a weak electrolyte, does not completely dissociates in water. So regardless of the concentration of acetic acid, the pH of 0.1 M acetic acid is higher.
CH₃COOH + H₂O → CH₃COO⁻ + H₃O⁺
HCl is a strong acid which dissociates into H⁺ and Cl⁻ ions in the water. In aqueous, the H⁺ joins a water molecule to form a hydronium ion, H₃O⁺.
HCl + H₂O → H₃O⁺ + Cl⁻
As pH = -log [H⁺], therefore lesser the [H⁺], greater will be the pH. HCl gives more H⁺ than acetic acid, therefore, pH of acetic acid is higher than HCl.
To learn more about pH,
https://brainly.com/question/14804040
#SPJ4
.Copper wire is used to transfer electricity.
There are 19.3 grams of gold in one cubic centimeter.
Iron turns to liquid at 1,534.85°C.
Silver is very easy to bend.
Fluorite is a green crystal.
Answer:
What is the question?
Explanation:
This is a answer.
A sample of nitrogen gas is contained in a piston with a freely moving cylinder. At 0°c, the volume of the gas is 371 ml. To what temperature must the gas be heated to occupy a volume of 557 ml?.
A sample of nitrogen gas is contained a piston with a freely moving cylinder in a piston with a freely moving cylinder at 0° C , the volume of the gas 371 ml. the temperature must the gas be heated a volume of 557 ml is 123.091°C
According to the Charles's law,
V1 / T1 = V2 / T2
here,
V1 = 371 ml
V2= 571 ml
T1 = 0°C = 273 K
T2 = ?
putting the values in the formula ,
V1 / T1 = V2 / T2
T2 = ( T1 × V1) / V1
= (273 K) × ( 557 ml) / 371 ml
= 152061 K / 371
= 409.8 K
In °C = 409.8 - 273
136.8 °C
Thus,A sample of nitrogen gas is contained a piston with a freely moving cylinder in a piston with a freely moving cylinder at 0° C , the volume of the gas 371 ml. the temperature must the gas be heated a volume of 557 ml is 136.8 °C.
To learn more about Charles's law here
https://brainly.com/question/16927784
#SPJ4
(b) Describe how copper sulfate solution is obtained from the plants used in
phytomining.
Plants are grown in soil that contains low grade ore. the plants absorb metal ions through their roots and concentrate these ions in their cells. the plants are harvested and burnt. the ash left behind contains metal compounds.
I hope this helps :)
All chemical reactions obey the law of conservation of mass.
Give
the reason why the reaction between hydrochloric acid and calcium carbonate appears not to show conservation of mass.
The reason the reaction between hydrochloric acid and calcium carbonate appears not to obey the law of conservation of mass is the evolution of carbon dioxide gas.
What is the law of conservation of mass?The law states that in every chemical reaction, the mass of the participating atom is conserved but the atoms themselves can change forms.
Thus, for every atom, the mass before the reaction must also be equal to the mass after the reaction.
So, if two substances A (1 g) and B (1 g) react, the products should weigh: 1 + 1 = 2 g.
Now, in the case of the reaction between hydrochloric acid and calcium carbonate, something happens.
[tex]CaCO_3 + 2HCl -- > CaCl_2 + H_2O + CO_2[/tex]
One of the products formed is carbon dioxide gas. Unless the reaction vessel is sealed, the gas will escape and the weight of the products left will be less that the reactants.
More on the law of conservation of mass can be found here: https://brainly.com/question/28711001
#SPJ1
If 1.50 g of h2c2o4 . 2h2o were heated to drive off the water of hydration, how much anhydrous h2c2o4 would remain?
If 1.50 g of H₂C₂O₄.2H₂O were heated to drive off the water of hydration, 1.071 g of anhydrous H₂C₂O₄ would remain.
The balanced chemical equation of reaction is :
H₂C₂O₄.2H₂O → H₂C₂O₄ + 2H₂O
First calculate the molecular weight of hydrated H₂C₂O₄ -
Using the molecular masses of -
O = 16 g/mol, C = 12 g/mol, and H = 1 g/mol
Total mass of compound = 126 g/mol
Molecular mass of H₂C₂O₄ = 90 g/mol
and, molecular mass of water of hydration = 36 g/mol
The percentage of H₂C₂O₄ in H₂C₂O₄.2H₂O is -
% H₂C₂O₄ = 90 g/mol = 0.714 %
126 g/mol
To calculate remainingIf 1.50 g of H₂C₂O₄.2H₂O were heated to drive off the water of hydration, 1.071 g of anhydrous H₂C₂O₄ would remain.
The balanced chemical equation of reaction is :
H₂C₂O₄.2H₂O → H₂C₂O₄ + 2H₂O
First calculate the molecular weight of hydrated H₂C₂O₄ -
Using the molecular masses of -
O = 16 g/mol, C = 12 g/mol, and H = 1 g/mol
Total mass of compound = 166 g/mol
Molecular mass of H₂C₂O₄ = 126 g/mol
and, molecular mass of water of hydration = 36 g/mol
% H₂C₂O₄ = 126 g/mol = 0.7590
166 g/mol
75.90 % of 1.50 g = 0.714
To calculate remaining amount of anhydrous H₂C₂O₄,
we take percentage of anhydrous H₂C₂O₄ with the mass of hydrous compound which is heated.
71.4% of 1.50 g = 1.071 g
Therefore,
The anhydrous H₂C₂O₄ remaining is 1.071 g.
To learn more about the anhydrous compound,
brainly.com/question/25465144
#SPJ1
list the first 20 elements with their properties
H - Hydrogen
He - Helium
Li - Lithium
Be - Beryllium
B - Boron
C - Carbon
N - Nitrogen
O - Oxygen
F - Fluorine
Ne - Neon
Na - Sodium
Mg - Magnesium
Al - Aluminum
Si - Silicon
P - Phosphorus
S - Sulfur
Cl - Chlorine
Ar - Argon
K - Potassium
Ca - Calcium
take only in consideration the carbon–carbon bond in the molecules. assign the correct orbitals to the molecule groups. (orbitals might be used more than once or not at all).
Carbon bond in the molecules is only taken into consideration, thus assigning the correct orbitals to molecule group, we get the Option A ethylene.
Carbon-Carbon bondA covalent link between two carbon atoms is known as a carbon-carbon bond. The single bond, that is consisted of two electrons—one from each of the two atoms—is the most prevalent type.
One kind of hybridized orbital from each of the carbon atoms are contributing to the formation of the carbon-carbon single bond, which is also known as a sigma bond.
Carbon and carbon have what type of bond?They have an ionic bond
A covalent link involving two C atoms is known as a carbon-carbon bond. The single bond with two electrons—one from each of the two atoms—is the most well-known type.
What four different sorts of bonds can carbon form?A single carbon atom can also make four different kinds of bonds with all the other atoms.
One double bond and two types of single bonds and a total pair of double bonds.
To know more about Carbon bond visit:
https://brainly.com/question/4704641
#SPJ4
Complete Question
Take only in consideration the carbon-carbon bond in the molecules. Assign the correct orbitals to the molecule groups. (Orbitals might be used more than once or not at all).
A) Ethylene
B) Ethane
C) Acetylene
Forensic scientists use science to find evidence at a crime scene. Which sentence describes how forensic scientists could use observation to determine the time that a crime scene took place?
By looking at the body they can come up with an estimated time of how long it’s been without oxygen(dead).
What are some examples of situations in which gel electrophoresis is used and the types of molecules that scientists separate using the technique.
Answer:
When the molecules are placed in the individual wells they are all at the same distance because al the wells were created with the same comb. Gel electrophoresis is applying an electrical current to separate the molecules. Once gel electrophoresis is ran, the negative dyes will run towards the positive end of the gel and the positive dyes will run towards the negative end of the gel. The heavier dyes will run a shorter distance compared to the lighter dyes, this is how they are separated out.
Explanation:
Answer:
A situation gel electrophoresis is used in DNA fragments like in a crime scene or to distinguish species.
Explanation:
how many electrons are in 40 Ne?
40 Ne has 10 electrons which consist of 10 protons and 10 neutrons
Neon is a chemical element which is rare gas or noble gas as it has a stable octet electronic configuration, meaning it has 8 valence electrons in its outermost shell.
Neon belongs to group 0/VIII and period 1 of the periodic table.
What is an element?An element is a substance which takes part in a chemical reaction. There are different classes of elements which includes the metals, nonmetals and the metalloids.
So therefore, 40 Ne has 10 electrons which consist of 10 protons and 10 neutrons.
Learn more about elements:
https://brainly.com/question/1379504
#SPJ1
what four elements does halogen bond with?
fluorine, chlorine, bromine, and iodine,
An ancient copper coin was found to absorb 545.8 J of heat when the temperature increases 31.4°C. The specific heat of copper is 0.387 J/g'C. What is the mass of the copper coin?
The mass of the Copper coin is 44.9g
Given that,
q = 545.8 J ; c = 0.387 J/g°C ; ΔT = 31.4°C
To find the mass of the copper the following formula which is used to find the heat absorbed by a substance is to be used:
q = mcΔT
where
q = quantity of the heat
m = mass of the substance
c = specific heat capacity of the material
ΔT = change in the temperature
Therefore, on rearranging the formula to find the mass of copper coin we get,
m = q/cΔT
On substituting the values of q, c and ΔT we get
m = 545.8 J/(0.387 J/g°C * 31.4 °C)
On solving we get,
m = 44.9g
Therefore the mass of the copper coin is 44.9g.
To know more about specific heat capacity, click below
https://brainly.com/question/21406849
#SPJ9
A toy car has an initial velocity of 0m/s and a final velocity of 100m/s. this high speed projectile changes it's velocity in 10 seconds. what was the acceleration of the car? responses
The toy car that had an initial velocity of 0m/s and a final velocity of 100m/s had an acceleration of 10 m/s^2
The formula for Uniformly varied rectilinear motion (UVRM) and procedure we will use to solve this exercise is:
a = (vf - vi) /t
Where:
vf = final velocityvi = initial velocityt = timea = accelerationInformation about the problem:
vi= 0 m/svf= 100 m/st = 10 sa= ?Applying the acceleration formula, we have:
a = (vf - vi) /t
a = ( 100 m/s - 0 m/s) / 10 s
a = 100 m/s / 10 s
a = 10 m/s^2
What is acceleration?It is a physical quantity that indicates the variation of velocity as a function of time, it is expressed in units of distance per time squared e.g.: m/sec^2 ; km/h^2
Learn more about acceleration at: brainly.com/question/14344386
#SPJ4
Which combination of forces in the table below would allow the rocket to launch?
Find the feature not shared by lipids, nucleic acids, and proteins. First exclude the four features that are shared by all three classes of large molecules.
With the exclusion of the first four features that are shared by all three classes of large molecules. They can all form strings of hundreds of repeating monomer units". Option C
This is further explained below.
What is a monomer unit?Generally, A monomer is a molecule that, via a process known as polymerization, may interact with other monomer molecules to produce a longer polymer chain or three-dimensional network.
In conclusion, With the first four characteristics, which are shared by all three types of big molecules, are excluded. Each of them has the ability to create long, repeating monomer unit strings. Choice C
Read more about monomer units
https://brainly.com/question/8156064
#SPJ1
they can all form strings of hundreds of repeating monomer units".
cq
Find the feature not shared by lipids, nucleic acids, and proteins. First exclude the four features that are shared by all three classes of large molecules.
O They are all based on carbon.
O They are all made from a limited variety of different building blocks. They can all form strings of hundreds of repeating monomer units. OTheir building blocks contains H on one end and OH on the other end. They are all broken down by hydrolysis.
The actual density of a certain material is 7.48g/cm^3. a student measures the density of the same material as 7.2g/cm^3.what is the percent error of the measurement? answer in units of %
The actual density of a certain material is 7.48g/[tex]cm^{3}[/tex]. a student measures the density of the same material as 7.2g/[tex]cm^{3}[/tex]. the percent error of the measurement is 3.74 %.
Percent Error is defined as difference between experimental value and the theoretical value divided by theoretical value and multiply by 100.
Percent Error =( | experimental value - theoretical value | ) / 100 %
here,
experimental value = 7.2 g/ [tex]cm^{3}[/tex]
theoretical value = 7.48 g/[tex]cm^{3}[/tex]
percent error ( % error) = ( | 7.2 - 7.48 | ) / 7.48 × 100 %
=( 0.28 / 7.48 ) × 100 %
= 3.74 %
Thus,The actual density of a certain material is 7.48g/[tex]cm^{3}[/tex]. a student measures the density of the same material as 7.2g/[tex]cm^{3}[/tex]. the percent error of the measurement is 3.74 %.
To learn more about Percent error here
https://brainly.com/question/3670306
#SPJ4
How might the government make sure scientific research is done in an ethical
way?
A. By letting public opinion determine what is ethical in scientific
research
B. By taking away research funds if certain ethical standards are not
met
C. By encouraging scientists to perform within their own ideas of
right and wrong
OD. By allowing scientists to do what they think is best
Answer: By taking away research funds if certain standards are not met
PLEASE HELP QUICKLY I'M REALLY CONFUSED AND NEED THIS IS SIMPLE DEFINITION
why do positive ions grow from left to right, and negative from right to left?
Answer:
It is quite known that in case of electrolyte there are no electrons. The electric current is basically due to flow of ions.