Answer:
Dust Storms and desertification
Explanation:
I looked up the question and a lot of stuff about desertification came up
PLEASE HELP
NASA scientists have determined that the chance a single person would get hit by a piece of falling satellite is one in 3,200. What can you infer based on this probability?
A. Satellites that enter Earth’s atmosphere land mostly in the ocean.
B. NASA does a good job informing people of when satellites will enter the atmosphere.
C. Satellites that enter Earth’s atmosphere land mostly in unpopulated areas.
D. Much of a satellite is destroyed during the process of entering Earth’s atmosphere.
Answer:
The Answer Is Much of a satellite is destroyed during the process of entering Earth’s atmosphere.
Explanation:
Right On Edge
if it took 2 hours to clean 4 houses how many houses could be cleaned in 3 hours
Answer:
6 houses
Explanation:
because
2hrs=4 houses which means you are cleaning 2houses in one hour
so in 3 hours you will houses because you will clean 2 houses in one hour
I hope this helped you sorry if I am wrong
Who has good grades in school like A's B's dm me
Answer:
I do
Explanation:
Describe three functions of an operating system
Answer:
1. Booting. Booting is a process of starting the computer operating system starts the computer to work. It checks the computer and makes it ready to ...
2. Memory Management.
3. Loading and Execution.
Hope dis helpz!
Visual aids are useful for all of the following reasons except
Answer:
B
Explanation:
their presence allows the speaker to take a rest from talking
I couldnt see the question
How many meters is equivalent to a mile? Give your answer to the nearest meter.
Answer:
Around 1609 meters.
Explanation:
1609.3 meters rounded to 1609.
Which of the following is NOT an application for robotics
The options which are not an application for robotics are:
C. Outside exercise.
D. Kitchen appliances.
What is robotics?Robotics can be defined as a subfield of computer technology and engineering that typically deals with the design, development construction, operation, and application (use) of advanced computer systems known as robots, especially for the performance of certain tasks.
This ultimately implies that, outside exercise and kitchen appliances are not an application for robotics.
Read more on robotics here: https://brainly.com/question/10387419
#SPJ2
Why might an insulation worker be necessary in the demolition phase of a reconstruction project?
They can eliminate the need for new insulation
They can verify that the old insulation was inadequate.
They can serve as general laborers for the project.
They can remove possibly toxic materials safely
Answer:
i think its the last one im not 100 tho
A 1/4" nut driver with a 1.52 inch diameter handle is used to install a 14" 6 UNC
bolt into a robotic arm.
Determine the circumference where the effort is applied.
sion
Round to the nearest 0.00
Answer:
2.23
Explanation:
so wee add
Natalie solved the problem below incorrectly. Identify his error and justify your reasoning. −19+3x−11+2x=2 5x−19−11=2 5x−30=2 5x=−28 x=−5.6
Task 1
Water is retained in a 1 m wide rectangular section channel by a sluice gate that can
pivot about its base, as shown below. Determine the total force on the gate due to the
water, the position where it is considered to act and the tension in the horizontal
retaining cable attached to the top of the gate when the depth of water in the channel
is 1.5 m. The density of water is 1000 kg/m3.
Cable tension = T
2 m
1.5 m
Pivot
Answer:
I dont understand your question.
Explanation:
Would be much appreciated if someone could help with this will give brainiest.
Answer: both mm and inches on each dimension in a sketch (with the main dimension in one format and the other in brackets below it), in the way you can have dual dimensions shown when detailing an idw view.
personally think it would look a mess/cluttered with even more text all over the sketch environment, but everyone's differenent.
If it's any help - you know you can enter dimensions in either format? If you're working in mm you can still dimension a line and type "2in" and vice-versa. Probably know this already, but no harm saying it, just in case.
You can enter the units directly in or mm and Inventor will convert to current document settings (which you can change - maybe someone can come up with a simple toggle icon to toggle the document settings). Tools>Document Settings>Units
Unlike SolidWorks when you edit the dimension the original entry shows in the dialog box so it makes it easy to keep track of different units even if they aren't always displayed. (SWx does the conversion or equation and then that is what you get.)
I work quite a bit in inch and metric and combination (ex metric frame motor on inch machine) and it doesn't seem to be a real difficulty to me.
Which edge of a table saw goes along the fence? The jointed edge or rough edge?
Answer:
Jointed edge
Explanation: